Jump to content


Photo

Post Your Videos


  • Please log in to reply
259 replies to this topic

#46 BrightStar

BrightStar

    Pyro Forum Regular

  • General Public Members
  • PipPipPip
  • 900 posts

Posted 02 June 2008 - 06:16 PM

Here are some vids of my first 3" shell and a 3" star mine.


Good work! Did you have two types of stars in the shell? It looked like there were glitters and charcoal streamers in there. The timing looked fine.

Try pasting 3 or 4 layers of kraft over the plastic or a few wraps of fibreglass packing tape - it does improve the break. I find that my plastic shells tear apart around the seam when they burst - the joint made with plumbers solvent cement is stonger than the shell case itself. 5g or so of granulated hot whistle sprinkled in will also do wonders :)

The mine was impressive - maybe try a slightly faster star (or one with finer charcoal) for less fallout.

Edited by BrightStar, 02 June 2008 - 08:35 PM.


#47 t1tan

t1tan

    Member

  • General Public Members
  • PipPip
  • 14 posts

Posted 02 June 2008 - 09:42 PM

Made a small 1" plastic ball shell.
Pulverone break.

http://homepage.ntlw...ve/redshell.MOV

Not all the stars lit as you can see, i think ill have to prime them again and make sure their completely covered.

#48 digger

digger

    Pyro Forum Top Trump!

  • UKPS Members
  • 1,961 posts

Posted 02 June 2008 - 09:52 PM

Made a small 1" plastic ball shell.
Pulverone break.

http://homepage.ntlw...ve/redshell.MOV

Not all the stars lit as you can see, i think ill have to prime them again and make sure their completely covered.


Very Good

How big are the stars in this shell, what formula are they, what method did you use to make them and what size are they?

Digger
Phew that was close.

#49 ridley

ridley

    Member

  • General Public Members
  • PipPip
  • 35 posts

Posted 02 June 2008 - 10:10 PM

Good work! Did you have two types of stars in the shell? It looked like there were glitters and charcoal streamers in there. The timing looked fine.

Try pasting 3 or 4 layers of kraft over the plastic or a few wraps of fibreglass packing tape - it does improve the break. I find that my plastic shells tear apart around the seam when they burst - the joint made with plumbers solvent cement is stonger than the shell case itself. 5g or so of granulated hot whistle sprinkled in will also do wonders :)

The mine was impressive - maybe try a slightly faster star (or one with finer charcoal) for less fallout.


Both had glitter and chrys #6 in them. Ill try the tape and some flash/whistle in there next time.

Ridley

#50 t1tan

t1tan

    Member

  • General Public Members
  • PipPip
  • 14 posts

Posted 03 June 2008 - 12:40 PM

The stars are cut, to about 8-10mm square. about 2-3mm thick. They are buell red with meal+al prime.

#51 Bonny

Bonny

    Pyro Forum Regular

  • General Public Members
  • PipPipPip
  • 538 posts

Posted 04 June 2008 - 12:53 PM

Here are some clips from my "show" last weekend.

2- 2 inch mines: tigertail/veline blue, veline red


6 -1 inch mini mines with mixed veline stars (leftover broken pcs), dragon eggs and silver flying fish fuse.


30 shot reloadable fan cake (passfire style)
Filled with 1" white,tigertail,shimizu willow +Ti, firefly comets and veline with dragon eggs matrix comet/stars.


See my post in cylindrical shells thread for some shells I fired.

#52 ultrabuf

ultrabuf

    Member

  • General Public Members
  • PipPip
  • 16 posts

Posted 09 June 2008 - 01:45 AM

3 inch D1 Glitter with Tigertail Ring
http://s231.photobuc...gertailRing.flv

4 inch Tigertail ball shell (my first 4")
http://s231.photobuc...ReeperSilve.flv

4" can, my first attempt at farfalle didnt quite get the effect I wanted, but still kinda neat.
http://s231.photobuc...odifiedReep.flv

Edited by ultrabuf, 09 June 2008 - 03:52 AM.


#53 Techohead

Techohead

    Member

  • General Public Members
  • PipPip
  • 40 posts

Posted 09 June 2008 - 03:25 AM

i would love to get some input from all the pyro's out there on my shells and rockets and such. i've only been doing pyrotechnics for about 8 months, but i'm getting the hang of it. please note that everything i make is made souly from black powder ingredients. i have no access to metal powders or perchlorates, so with that in mind, i think i've done pretty well. bp lift, bp break, bp rocket fuel, bp stars...

my latest aerial shell 2" chrysthanthemum 6:

My latest rocket with report header:

My petrol fuelled flamethrower:

homemade 1" cannon:

enjoy, techohead...

#54 Pyrogeorge

Pyrogeorge

    Member

  • General Public Members
  • PipPip
  • 142 posts

Posted 13 June 2008 - 12:10 PM

I tested my stars yesterday

BP star:

TT star:

both fired with flare pistol

#55 cplmac

cplmac

    Member

  • General Public Members
  • PipPip
  • 194 posts

Posted 22 June 2008 - 06:41 AM

3lb whistle rocket headed with red to white to blue to report box stars

This is a test of some box stars I've been toying with.
Great videos everyone, keep 'em coming.

#56 Pretty green flames

Pretty green flames

    Pyro Forum Regular

  • General Public Members
  • PipPipPip
  • 689 posts

Posted 02 July 2008 - 05:33 AM

After a bit of a break I finally sent some shells in the air





All of them are 4" rounds.

#57 Bonny

Bonny

    Pyro Forum Regular

  • General Public Members
  • PipPipPip
  • 538 posts

Posted 04 July 2008 - 12:25 PM

After a bit of a break I finally sent some shells in the air





All of them are 4" rounds.



Nice shells PGF. What silver streamer formula were you trying?

#58 Pretty green flames

Pretty green flames

    Pyro Forum Regular

  • General Public Members
  • PipPipPip
  • 689 posts

Posted 04 July 2008 - 12:40 PM

I was using this one, was a bit dissappointed to be honest, I was expecting more of a long tail though

Potassium nitrate..........................55
Aluminum (Bright flake).................15
Boric acid......................................2
Fine charcoal.................................10
(bound with gelatine)

#59 Bonny

Bonny

    Pyro Forum Regular

  • General Public Members
  • PipPipPip
  • 538 posts

Posted 04 July 2008 - 07:13 PM

I was using this one, was a bit dissappointed to be honest, I was expecting more of a long tail though

Potassium nitrate..........................55
Aluminum (Bright flake).................15
Boric acid......................................2
Fine charcoal.................................10
(bound with gelatine)



Too bad about the tail. I guess I won't try that one as a streamer star. I haven't made any silver streamers yet. I did mix up some of that silver cascade you have on APC. I still have to step prime, but burn rate on 3/8" to 1/2" stars looks good for 3" shells.

#60 Pretty green flames

Pretty green flames

    Pyro Forum Regular

  • General Public Members
  • PipPipPip
  • 689 posts

Posted 04 July 2008 - 07:55 PM

Cool, hope to se a video of the silver cascade up in the air.




1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users